I've configured FastEcho I think as it should be but I keep getting this
error message when I run fastecho scan.

"Can't export message in area FIDOTEST without active downlinks."

I went to node configuration and entered info for my uplink, But I will not have any downlinks.

Any help and is this still registerable?

Ruben Figueroa aka Zazz
Mystic Prison Board Sysop
telnet://pbmystic.rdfig.net:24
Web: www.rdfig.net

--- Mystic BBS v1.12 A43 2019/03/03 (Windows/32)
* Origin: Mystic Prison Board*Mesquite Tx*pb.darktech.org:24 (1:124/5014)

On 2019 Jul 16 18:03:54, you wrote to All:

"Can't export message in area FIDOTEST without active downlinks."

I went to node configuration and entered info for my uplink, But I will

not

have any downlinks.

a link is both up and down... you must have at least one system linked... generally this will be the one link you get your mail for the area from... thus
"downlink" since you are "down stream" from them...

Any help and is this still registerable?

yes... fill out the application form and send it to toby...

https://www.softeq.de/old/Products/FastEcho/fastecho.html

use the author link at the top of the page in the first paragraph... he does have a fidonet address but the web/email will likely work better/faster...

)\/(ark

And to this end they built themselves a stupendous super-computer which was
so amazingly intelligent that even before its data banks had been connected
up it had started from "I think therefore I am" and got as far as deducing
the existence of rice pudding and income tax before anyone managed to turn
it off.
... It is further to Chicago than by bus.
---
* Origin: (1:3634/12.73)

a link is both up and down... you must have at least one system linked... generally this will be the one link you get your mail for the area
from... thus "downlink" since you are "down stream" from them...

Found out where to link messages to the uplink so traffic is flowing.

yes... fill out the application form and send it to toby...

https://www.softeq.de/old/Products/FastEcho/fastecho.html

use the author link at the top of the page in the first paragraph... he does have a fidonet address but the web/email will likely work better/faster...

Well I did email, a couple of times, been a few days, but I didn't send in
the application so I'll do that now.

Thanks

Ruben Figueroa aka Zazz
Mystic Prison Board Sysop
telnet://pbmystic.rdfig.net:24
Web: www.rdfig.net

--- Mystic BBS v1.12 A43 2019/03/03 (Windows/32)
* Origin: Mystic Prison Board*Mesquite Tx*pb.darktech.org:24 (1:124/5014)

Zazz wrote to All <=-

I've configured FastEcho I think as it should be but I keep getting
this error message when I run fastecho scan.

"Can't export message in area FIDOTEST without active downlinks."

I went to node configuration and entered info for my uplink, But I will not have any downlinks.

Any help and is this still registerable?

I believe you should still be able to get a free key for it by emailing
the author. Also, you need to go into the FIDOTEST echo configuration
and make sure you have at least one node listed in (I believe) the
"Export To" section of the echo area entry form.

... The number you have dailed...Nine-one-one...has been changed.
___ MultiMail/Win v0.52

--- Mystic BBS/QWK v1.12 A43 2019/02/03 (Windows/32)
* Origin: Omicron Theta * Southaven MS * winserver.org:2300 (1:116/18)